BDS 8" 4-Link Lift Kit (2019-2021 Dodge/Ram 2500 Truck 4WD w/ Rear Coil Springs) (1727H) BDS 8" 4-Link Lift Kit (2019-2021 Dodge/Ram 2500 Truck 4WD w/ Rear Coil Springs) (1727H) BDS Suspension DIESEL MODELS ONLY BDS Suspension expands its listings for the late model RAM 2500 4WD diesel trucks with new 8" 4-link conversion systems. Up front these systems use a pair of 8" diesel specific progressive rate coil springs to provide the extra height and smooth controlled performance in the harshest of terrains. A forged drop pitman arm is supplied to correct steering angles along with a HD bar drop bracket to re-center the front axle. A pair of sway bar drop brackets reposition the OE sway bar for optimal performance along with extended polyurethane bump stops to limit up travel and brake line brackets to allow full droop. To correct the front suspension geometry at the new height, the factory stamped steel radius arms are converted over to 4-link using a pair of 1/4" steel brackets and high strength upper and lower control arms designed to limit caster control throughout suspension travel for more predictable handling characteristics. Also supplied are your choice of BDS NX2 gas shocks or FOX 2.0 Performance Series IFP gas shocks for improved ride and performance. At 8" of lift it is critical to make front driveline adjustments to maintain use of 4WD due to the increased operating angle. To do this, BDS Suspension provides a heavy duty replacement transmission crossmember as well as a transfer case indexing ring to reposition the front driveline output which will need to be used in combination with an aftermarket front driveshaft (not included with kit). In the rear, careful consideration was taken to design the system for load carrying capacity, handling, and ride quality. The factory coil positioning inside the frame rails is sufficient at smaller heights, but at 8" of lift needed to be modified to increase stability. Similar to the 14-18 models, the rear springs have been outboarded by 8" per side (16" total) using a set of bolt-on mounts. This new position mimics that of a leaf spring on the 3500 models and provides increased stability without compromising ride quality. The new upper and lower coil seats locate off of existing features on the frame and axle, requiring only minor drilling for mounting hardware. The new position allows for a much shorter and more stable coil spring design. This virtually eliminates any chance of coil bowing and ensures the coils react predictably throughout the full range of travel. In addition to the coil springs/mounts, a new track bar relocation system is included to properly set the rear roll-center height and center the axle under the vehicle. The rear track bar relocation includes a new heavy duty adjustable track bar. The track bar uses high-durometer polyurethane bushings at the frame and an adjustable forged COM bearing joint at the axle. Extended rear sway bar links round out the rear suspension components. Rounding out the rear of this kit is your choice of NX2 series or Fox 2.0 Performance Series gas shocks. Get the look and the ride you are after with these new 8" 4-link systems from BDS Suspension.  Important Kit Notes 1. Aftermarket driveshaft is required2. Will not work with Megacab models3. For use on diesel models only4. Fits rear coil sprung models only (will not fit air-ride models)5. This kit requires the use of an aftermarket front driveshaft (not provided) in addition to the (provided) indexing ring kit - BDS122624 (6-bolt) or BDS122421 (8-bolt). Both must be installed, however due to variations between truck configurations we recommend installing the kit prior to taking measurements for the aftermarket front driveshaft to ensure correct length. Vehicle can be driven without front driveshaft. Kit was tested with a Drive Line Plus flange and driveshaft, however other high angle driveshaft options can be used. Specifications Lift Height Front (base kit): 8" Coil SpringsRear (base kit): 5" Block & AAL  Tire and Wheel Combinations 40x13.50 w/20x9 and 4.5-5.5" back spacing38x15.50 w/20x21 and 5.5" back spacing*Trimming may be required*  Installation Est. Installation: 8-10 hoursDifficulty Level (easy 1 - 5 complicated): 4 InstructionsClick Here for PDF 1 of 3Click Here for PDF 2 of 3 Click Here for PDF 3 of 3  Vehicle Fitment Data Make Model Type Year Range Dodge / Ram 2500 Truck 4WD w/ Rear Coil Springs 2019-2021   Base Kit Components These components are subject to change based upon your selections. Qty Part# Description (1) 012434 2019-2021 Ram 2500/3500 4-Link Box Kit - (1) 012627 2019-2021 Ram 2500 6" Rear Box Kit (1) 012811 2019-2021 Ram 2500/3500 8in 4- Link Fron (1) 032619 2014-2021 Ram 2500 Rear 6" Coil Box Kit (2) 032802 2013-2021 Ram 3500 8in Front Coil-Dsl (S (1) 122624 2019-2021 Ram 2500/3500 T-Case Index - 6 (2) 85754 NX² Shock Absorber (2) 85763 NX² Shock Absorber

BDS 8" 4-Link Lift Kit (2019-2021 Dodge/Ram 2500 Truck 4WD w/ Rear Coil Springs) (1727H)

Code: 1727H
$3,966.15
In Stock
  • FREE SHIPPING

  • 30 DAY RETURNS

  • LIVE SUPPORT

DIESEL MODELS ONLY

BDS Suspension expands its listings for the late model RAM 2500 4WD diesel trucks with new 8" 4-link conversion systems.

Up front these systems use a pair of 8" diesel specific progressive rate coil springs to provide the extra height and smooth controlled performance in the harshest of terrains. A forged drop pitman arm is supplied to correct steering angles along with a HD bar drop bracket to re-center the front axle. A pair of sway bar drop brackets reposition the OE sway bar for optimal performance along with extended polyurethane bump stops to limit up travel and brake line brackets to allow full droop. To correct the front suspension geometry at the new height, the factory stamped steel radius arms are converted over to 4-link using a pair of 1/4" steel brackets and high strength upper and lower control arms designed to limit caster control throughout suspension travel for more predictable handling characteristics. Also supplied are your choice of BDS NX2 gas shocks or FOX 2.0 Performance Series IFP gas shocks for improved ride and performance.

At 8" of lift it is critical to make front driveline adjustments to maintain use of 4WD due to the increased operating angle. To do this, BDS Suspension provides a heavy duty replacement transmission crossmember as well as a transfer case indexing ring to reposition the front driveline output which will need to be used in combination with an aftermarket front driveshaft (not included with kit). In the rear, careful consideration was taken to design the system for load carrying capacity, handling, and ride quality. The factory coil positioning inside the frame rails is sufficient at smaller heights, but at 8" of lift needed to be modified to increase stability. Similar to the 14-18 models, the rear springs have been outboarded by 8" per side (16" total) using a set of bolt-on mounts. This new position mimics that of a leaf spring on the 3500 models and provides increased stability without compromising ride quality. The new upper and lower coil seats locate off of existing features on the frame and axle, requiring only minor drilling for mounting hardware. The new position allows for a much shorter and more stable coil spring design. This virtually eliminates any chance of coil bowing and ensures the coils react predictably throughout the full range of travel. In addition to the coil springs/mounts, a new track bar relocation system is included to properly set the rear roll-center height and center the axle under the vehicle. The rear track bar relocation includes a new heavy duty adjustable track bar. The track bar uses high-durometer polyurethane bushings at the frame and an adjustable forged COM bearing joint at the axle. Extended rear sway bar links round out the rear suspension components. Rounding out the rear of this kit is your choice of NX2 series or Fox 2.0 Performance Series gas shocks.

Get the look and the ride you are after with these new 8" 4-link systems from BDS Suspension.
 

Important Kit Notes

1. Aftermarket driveshaft is required
2. Will not work with Megacab models
3. For use on diesel models only
4. Fits rear coil sprung models only (will not fit air-ride models)
5. This kit requires the use of an aftermarket front driveshaft (not provided) in addition to the (provided) indexing ring kit - BDS122624 (6-bolt) or BDS122421 (8-bolt). Both must be installed, however due to variations between truck configurations we recommend installing the kit prior to taking measurements for the aftermarket front driveshaft to ensure correct length. Vehicle can be driven without front driveshaft. Kit was tested with a Drive Line Plus flange and driveshaft, however other high angle driveshaft options can be used.

Specifications

Lift Height
Front (base kit): 8" Coil Springs
Rear (base kit): 5" Block & AAL
 
Tire and Wheel Combinations
40x13.50 w/20x9 and 4.5-5.5" back spacing
38x15.50 w/20x21 and 5.5" back spacing
*Trimming may be required*
 

Installation

Est. Installation: 8-10 hours
Difficulty Level (easy 1 - 5 complicated): 4

Instructions
Click Here for PDF 1 of 3
Click Here for PDF 2 of 3
Click Here for PDF 3 of 3
 

Vehicle Fitment Data

Make Model Type Year Range
Dodge / Ram 2500 Truck 4WD w/ Rear Coil Springs 2019-2021
 

Base Kit Components

These components are subject to change based upon your selections.
Qty Part# Description
(1) 012434 2019-2021 Ram 2500/3500 4-Link Box Kit -
(1) 012627 2019-2021 Ram 2500 6" Rear Box Kit
(1) 012811 2019-2021 Ram 2500/3500 8in 4- Link Fron
(1) 032619 2014-2021 Ram 2500 Rear 6" Coil Box Kit
(2) 032802 2013-2021 Ram 3500 8in Front Coil-Dsl (S
(1) 122624 2019-2021 Ram 2500/3500 T-Case Index - 6
(2) 85754 NX² Shock Absorber
(2) 85763 NX² Shock Absorber

DIESEL MODELS ONLY

BDS Suspension expands its listings for the late model RAM 2500 4WD diesel trucks with new 8" 4-link conversion systems.

Up front these systems use a pair of 8" diesel specific progressive rate coil springs to provide the extra height and smooth controlled performance in the harshest of terrains. A forged drop pitman arm is supplied to correct steering angles along with a HD bar drop bracket to re-center the front axle. A pair of sway bar drop brackets reposition the OE sway bar for optimal performance along with extended polyurethane bump stops to limit up travel and brake line brackets to allow full droop. To correct the front suspension geometry at the new height, the factory stamped steel radius arms are converted over to 4-link using a pair of 1/4" steel brackets and high strength upper and lower control arms designed to limit caster control throughout suspension travel for more predictable handling characteristics. Also supplied are your choice of BDS NX2 gas shocks or FOX 2.0 Performance Series IFP gas shocks for improved ride and performance.

At 8" of lift it is critical to make front driveline adjustments to maintain use of 4WD due to the increased operating angle. To do this, BDS Suspension provides a heavy duty replacement transmission crossmember as well as a transfer case indexing ring to reposition the front driveline output which will need to be used in combination with an aftermarket front driveshaft (not included with kit). In the rear, careful consideration was taken to design the system for load carrying capacity, handling, and ride quality. The factory coil positioning inside the frame rails is sufficient at smaller heights, but at 8" of lift needed to be modified to increase stability. Similar to the 14-18 models, the rear springs have been outboarded by 8" per side (16" total) using a set of bolt-on mounts. This new position mimics that of a leaf spring on the 3500 models and provides increased stability without compromising ride quality. The new upper and lower coil seats locate off of existing features on the frame and axle, requiring only minor drilling for mounting hardware. The new position allows for a much shorter and more stable coil spring design. This virtually eliminates any chance of coil bowing and ensures the coils react predictably throughout the full range of travel. In addition to the coil springs/mounts, a new track bar relocation system is included to properly set the rear roll-center height and center the axle under the vehicle. The rear track bar relocation includes a new heavy duty adjustable track bar. The track bar uses high-durometer polyurethane bushings at the frame and an adjustable forged COM bearing joint at the axle. Extended rear sway bar links round out the rear suspension components. Rounding out the rear of this kit is your choice of NX2 series or Fox 2.0 Performance Series gas shocks.

Get the look and the ride you are after with these new 8" 4-link systems from BDS Suspension.
 

Important Kit Notes

1. Aftermarket driveshaft is required
2. Will not work with Megacab models
3. For use on diesel models only
4. Fits rear coil sprung models only (will not fit air-ride models)
5. This kit requires the use of an aftermarket front driveshaft (not provided) in addition to the (provided) indexing ring kit - BDS122624 (6-bolt) or BDS122421 (8-bolt). Both must be installed, however due to variations between truck configurations we recommend installing the kit prior to taking measurements for the aftermarket front driveshaft to ensure correct length. Vehicle can be driven without front driveshaft. Kit was tested with a Drive Line Plus flange and driveshaft, however other high angle driveshaft options can be used.

Specifications

Lift Height
Front (base kit): 8" Coil Springs
Rear (base kit): 5" Block & AAL
 
Tire and Wheel Combinations
40x13.50 w/20x9 and 4.5-5.5" back spacing
38x15.50 w/20x21 and 5.5" back spacing
*Trimming may be required*
 

Installation

Est. Installation: 8-10 hours
Difficulty Level (easy 1 - 5 complicated): 4

Instructions
Click Here for PDF 1 of 3
Click Here for PDF 2 of 3
Click Here for PDF 3 of 3
 

Vehicle Fitment Data

Make Model Type Year Range
Dodge / Ram 2500 Truck 4WD w/ Rear Coil Springs 2019-2021
 

Base Kit Components

These components are subject to change based upon your selections.
Qty Part# Description
(1) 012434 2019-2021 Ram 2500/3500 4-Link Box Kit -
(1) 012627 2019-2021 Ram 2500 6" Rear Box Kit
(1) 012811 2019-2021 Ram 2500/3500 8in 4- Link Fron
(1) 032619 2014-2021 Ram 2500 Rear 6" Coil Box Kit
(2) 032802 2013-2021 Ram 3500 8in Front Coil-Dsl (S
(1) 122624 2019-2021 Ram 2500/3500 T-Case Index - 6
(2) 85754 NX² Shock Absorber
(2) 85763 NX² Shock Absorber
IMPORTANT COVID-19 NOTE: 
Our warehouses are open and continuing to ship orders. However, please note that nearly all automotive parts manufacturers, distribution centers, and logistics centers face backorders and delays in order fulfillment.
 
If an item is unexpectedly out of stock or delayed, Lift Kits 4 Vets will make an effort to notify the customer, provide order status updates, and expedite the fulfillment process. If you have any questions pertaining to your order status, please use the Contact link above. We thank you for your patience and understanding.
 
Product Availability

To check stock levels, use our Live-Chat feature or Contact page. See the Lead Times tab for average order fulfillment times by manufacturer.

Note that some items ship directly from the manufacturer. For these items, the manufacturer may not provide real-time inventory data to Lift Kits 4 Vets and backorders are possible. If an item is unavailable, Lift Kits 4 Vets will contact the buyer with an estimated ship date. In the event of excessive manufacturer backorders or delays, Lift Kits 4 Vets may opt to cancel the order and provide a full refund.

Shipping

Lift Kits 4 Vets provides shipping within the contiguous 48 states only. For orders outside of this area, please use the Contact page prior to placing your order. Items shipped by ground or LTL generally arrive within 1-5 days from date of shipment. Lift Kits 4 Vets is not responsible for carrier shipping delays.

Returns & Refunds

Items in their original condition may be returned within 30 days from the date of purchase for a full refund. Items may NOT be returned once packaging has been opened or the item has been installed, otherwise used, or damaged. The buyer is responsible for all return shipping charges. Returns and refunds may be requested through the Contact page.

Note: Do NOT ship items back until you have received a return authorization, as items may be returned to a facility other than their point of origin. Refunds will generally be processed within 48 business hours of receipt at our warehouse in order to allow for inspection and processing.

Product Data
Lift Kits 4 Vets provides product data (including but not limited to item descriptions, important notes, and fitment information) as a courtesy only. This information is provided by product manufacturers and is assumed to be accurate at the time of publishing. Though Lift Kits 4 Vets may periodically audit and update some product information based upon manufacturer's published data revisions, Lift Kits 4 Vets does not guarantee the accuracy of any product data. Lift Kits 4 Vets reserves the right to update product data as necessary and without notice, and will not be held responsible for misprints, or changes/variations made by vehicle manufacturers. Customers should consult the product manufacturer's website for the most up-to-date product data.
 
Markdown & Open Box Items
Markdown and Open Box items are offered at a discount as they have either been overstocked, slightly damaged, and/or returned from a previous customer. Items are sold "as-is." Lift Kits 4 Vets will indicate any damage found during the inspection process. Please note that this does not guarantee that all defects have been identified. Sales for all items in this category are final. No refunds, exchanges, or replacements are permitted. Some manufacturers may continue to warranty such items; however, the purchaser accepts that some manufacturers may not extend warranties to items in this category. Please refer to the individual product manufacturer's warranty page for details.

F.A.Q.
How do I request a return?
Use the Contact page, ensuring to include your order number, contact information, items for return, and reason for return. One of our team members will contact you with return shipping details and instructions. Additional information and documentation may be required.
Note: Some items must be returned directly to the manufacturer. Please do not ship items to  Lift Kits 4 Vets prior to return authorization and return instructions.

How do I request a replacement for a missing or damaged part?
Upon receipt, please inspect all orders for completion, accuracy, and damage. If packaging appears to be damaged, ensure to photograph the damage, as this may be required for a shipping carrier claim.
Use the Contact page, ensuring to include your order number, contact information, and description of the incorrect or damaged part(s). One of our team members will contact you to correct the issue.

What product warranties does Lift Kits 4 Vets offer?
Product warranties are solely offered by product manufacturers. Please refer to the product manufacturer's warranty statement. In the event of a warranty claim,  Lift Kits 4 Vets is available to assist with the manufacturer's required documentation. Please use the Contact page if assistance is required.
Estimated order processing times for in-stock items.
To check stock levels, use our Live-Chat feature or Contact page.
 
 Manufacturer Estimated Lead Time
BDS Suspension
1-2 Days
Morimoto 1-2 Days
ReadyLIFT Suspensions 1-7 Days
Rough Country 1-2 Days
Zone Offroad 1-2 Days